The Roadster FactoryThe Roadster Factory
TR6 Master Catalogue—Vol. 1 (Blue)
Table of Contents
LOGIN | VIEW CART | CHECKOUT
View Shopping Cart -
Search
                        10   < Previous Next >   10    
TRIUMPH TR6
PLATE AX
CARBURETTORS, 1971 MODEL YEAR
CARBURETTORS, 1971 MODEL YEAR
CARBURETTORS,
fitted from engine no. CC58258 approx.
up to CC75000 (Note possible overlap with previous
section.)
REAR CARBURETTOR ASSEMBLY
, Zenith Stromberg
1
model 175CD-2SE
Factory Rebuilt Unit
1
REAR CARBURETTOR ASSEMBLY,
Zenith Stromberg
1
model 175CD-2SE
Factory Rebuilt Unit
1
CARBURETTOR IDENTIFICATION CHECKLIST
· Metal tags attached to top cover screws should
read
C3385LH
and
C3385RH.
· Locate slanted pipes for attaching breather hoses
on front sides of both carbs in close to manifold;
these are the only breather hose connections.
· Locate fitting for installing suction pipe underneath
rear carb on mounting flange.
· There will be no vacuum fitting on top of inner mounting
flange, as there are no vacuum advance units on the
distributors fitted to this model range; if you find a threaded
hole in that position, it will not be drilled through into the
throttle passage, and you can plug it or leave it
unplugged as you wish.
· Bypass valves were identified by the letter
K
stamped
onto the upper flanges; they are not adjustable, and
they have no vacuum fittings.
· Identification characters stamped onto air cleaner faces
should be
065
and
089
with the letters
TA
and
TB
added as suffixes in various combinations.
· Vent hole in air cleaner face does not have brass bush.
· These carbs do not include a vent lever operating in
conjunction with throttle lever.
· Check cold start valves: cams will be marked
SRZ
;
bodies will be marked
AB
.
· Plugs in bottoms of float chambers will be flat with a
single screwdriver slot.
· Identifying individual model 175CD-2SE carbs can be tricky,
and the surest way is to retain the metal identification tags.
MAIN BODY DETAILS
AX1
Main Body Assembly
NSS
AX2
Screw
, throttle stop
2
AX3
Spring
, throttle stop
2
AX4
Screw
, idler trimming
2
AX5
Spring,
idler trimming
2
SUCTION CHAMBER DETAILS
AX6
DAMPER ASSEMBLY
, black plastic cap
2
Washer
2
Bushing
2
AX6
Ring, retaining
2
Plate No.
Part No.
Description
No. Off
SUCTION CHAMBER DETAILS--
Continued
AX7
Gasket
, damper
2
AX8
Air Valve and Guide Rod Assembly
NSS
AX9
Top Cover Assembly,
suction chamber
NSS
AX10
Screw and Washer Assembly,
securing top cover
6
assembly
Screw and Washer Assembly
, securing top cover
2
assembly, drilled for locking wire.
AX11
Diaphragm
2
AX12
Ring
diaphragm retaining ring
2
AX13
Screw
, securing diaphragm and retaining ring
8
AX14
Metering Needle
, adjustable (Coded B. 1AF)
2
AX15
Screw
, retaining metering needle
2
AX16
SCREW,
adjusting metering needle
2
AX17
"O" Ring,
oil sealing, adjusting screw
2
AX18
Clip,
spring, retaining adjusting screw
2
AX19
Spring,
air valve return
2
THROTTLE DETAILS
AX20
Spindle
, throttle, front carb
1
AX21
Spindle
, throttle rear, carb
1
AX22
Disc
, throttle
2
AX23
Screw
, securing throttle disc
4
AX24
SEAL ASSEMBLY
, throttle shaft
4
Seal
, throttle shaft (neoprene part only)
4
AX25
Spring,
throttle return
2
AX26
Lever
, throttle stop and fast idle
2
AX27
Screw
, fast idle
2
AX28
Nut
, locking screw
2
AX29
Washer
, spacing, rear carb only
1
AX30
Nut,
extension front carb only
1
AX31
ZEO17337
Washer
, spacing, rear carb only
2
AX32
Washer
, shakeproof, rear carb only
1
AX33
Nut,
rear carb only
1
FLOAT CHAMBER DETAILS
NEEDLE VALVE PACK
AX34
ZEB18535
Needle Valve
2
AX35
Washer
, needle valve
2
AX36
Float and Arm Assembly
2
AX37
Pin,
pivot, float assembly
2
AX38
Float Chamber
2
AX39
Gasket
, float chamber
2
AX40
PLUG
, sealing
2
AX41
`'O'' Ring
2
AX42
Screw and Lock Washer Assembly
, long, securing
8
float chamber
AX43
Screw and Lock Washer Assembly
, short, securing
8
float chamber
(Continued on next page.)
Plate No.
Part No.
Description
No. Off










                      10   < Previous | | | | | | Next >   10    

This Zenscript catalog conversion was performed by zeni.net internet services. If you have questions about this interface, contact support@zeni.net. Cookies and Javascript must be enabled for online ordering, but these pages should render in a viewable manner in any style-sheet capable browser.