TRIUMPH TR6
PLATE AR
EVAPORATIVE LOSS CONTROL SYSTEM
1970 UP TO 1971, U.S.A. MODELS
19
EVAPORATIVE LOSS CONTROL SYSTEM, 1970-1971, U.S.A. MODELS
EVAPORATIVE LOSS CONTROL SYSTEMS,
fitted
from comm. no. CC50000 up to CC75000 approx.
Please Note:
This section lists components for the
evaporative loss control systems which utilized an
``emission tank'' mounted on the inside of the R.H.
rear quarter. There were two slight variations of this
system. The earlier system, fitted from comm. no.
CC50000 up to CC55029 approx., included only a
single breather connection between the fuel tank
and the emission tank at the neck of the filler cap.
The later system, fitted from comm. no. CC55030
approx. up to CC75000 approx. utilized a four way
connector to allow three breather connections on
the fuel tank to one on the emission tank. The
emission tank was discontinued at comm. no.
CC75000 approx., and it was replaced with the
``separator canister'' listed in Section AS.
BREATHER CONNECTIONS,
fuel tank to emission tank,
fitted from comm. no. CC50000 approx. up to
CC55029 approx.
Connection,
breather, screwed into fuel filler neck
1
Washer,
fibre, sealing connection
1
Pipe,
nylon, from filler neck to emission tank
1
Connector,
rubber, nylon pipe to hose connection
1
fitted to filler neck
Connector,
rubber, nylon pipe to breather fitting on
1
emission tank
BREATHER CONNECTIONS,
fuel tank to emission tank,
fitted from comm. no. CC55030 approx. up to
CC75000 approx.
Connection,
breather, screwed into fuel filler neck
1
Washer,
fibre, sealing connection; deleted and
1
replaced with Loctite at an unknown comm. no.
Connection,
four-way
1
Connector,
rubber, between four-way connection
1
and filler neck
Hose,
rubber, between four-way connector and
1
breather fitting on R.H. top of fuel tank
Pipe,
nylon, between four-way connector and
1
breather fitting on L.H. top of fuel tank
Connector,
rubber, nylon pipe to four-way
2
connection and nylon pipe to breather fitting on
fuel tank
Pipe,
nylon, between four-way connection and
1
emission tank
Connector,
rubber, nylon pipe to four-way
2
connection and nylon pipe to breather fitting on
emission tank
Plate No.
Part No.
Description
No. Off
EVAPORATIVE LOSS CONTROL SYSTEMS--Continued
EMISSION TANK DETAILS
Emission Tank Assembly
1
Rivet,
imex, securing tank to inner rear fender
4
PIPE DETAILS,
from emission tank to carbon canister
Pipe,
nylon, rear, from emission tank, over top of
1
fuel tank, around trunk, and through trunk floor
Connector,
rubber, nylon pipe to fitting on emission
1
tank
Clip,
edge, securing nylon pipe to fuel tank flange
4
Clip,
nylon, single, anchoring nylon pipe to trunk
4
floor
Grommet,
rubber, between nylon pipe and hole in
1
trunk floor
Pipe,
nylon, front, from rear pipe to carbon canister
1
Connector,
rubber, front nylon pipe to rear nylon
1
pipe
Connector,
rubber, front nylon pipe to fitting on
1
carbon canister, fitted after comm. no.
CC55029 approx.
Connector,
rubber, front nylon pipe to fitting on
1
carbon canister, fitted after comm. no. CC55029
approx.
Finisher,
edge, rear shock absorber mounting
1
bracket
Clip,
pipe, nylon pipe to fuel pipe
5
Clip,
nylon, single, anchoring nylon pipe to chassis
1
frame
Clip,
fir tree, securing nylon pipe to R.H. radiator
1
stay
CARBON CANISTER DETAILS
CARBON CANISTER
1
Pad,
filter, lower
1
Bracket,
mounting, carbon canister
1
HARDWARE,
securing mounting bracket to radiator
stay
Screw,
set
1
Washer,
plain
1
Washer,
lock
1
Nut
1
HARDWARE,
clamping carbon canister into
mounting bracket
Screw,
set
1
Washer,
lock
1
Nut
1
Plate No.
Part No.
Description
No. Off
