TRIUMPH TR6
PLATE DK
REAR SUSPENSION
REAR SUSPENSION
Trailing Arm Assembly,
R.H.
1
Trailing Arm Assembly,
L.H.
1
Plug,
blanking hole in trailing arms, 7/8 inch diameter
4
Plug,
blanking hole in trailing arms, 1-1/8 inch diameter
4
Stud,
brake backplate and hub attachment
12
TRAILING ARM MOUNTINGS, ROAD SPRINGS, REBOUND
RUBBERS,
fitted up to comm. no. CC61570/CP52867
TRAILING ARM MOUNTING KIT
2
Bracket,
trailing arm mounting, inner (Identified by
2
one notch.)
Bracket,
trailing arm mounting, outer (Identified by
2
two notches.)
HARDWARE AND FITTINGS,
securing brackets to
chassis frame
Bolt
4
Bolt
4
Washer,
plain
8
Nut,
nyloc
8
Shim,
for adjusting alignment
A/R
HARDWARE AND FITTINGS,
securing trailing arms to
inner and outer brackets
Bush,
pressed into trailing arms
4
Bolt,
trailing arm pivot
4
Washer,
plain
4
Nut,
nyloc
4
Road Spring,
stock grade
2
Road Spring,
mild competition grade
2
Insulator,
rubber, rear road spring
4
Rebound Rubber Assembly,
mounted on chassis frame
2
Rebound Rubber Assembly,
mounted on trailing arms
2
TRAILING ARM MOUNTINGS, ROAD SPRINGS, REBOUND
RUBBERS,
fitted after comm. no. CC61570/CP52867
Please Note:
The factory made the changes listed
below to help correct the problem of rear end
`'squatting'' upon acceleration. Provided that items
are replaced in complete car sets, earlier TR6's may
benefit from the installation of the components listed
here.
TRAILING ARM MOUNTING KIT
2
Bracket,
trailing arm mounting, inner (Identified by
three notches.)
2
Bracket,
trailing arm mounting, outer (Identified by
one notch.)
2
Plate No.
Part No.
Description
No. Off
TRAILING ARM MOUNTINGS, ROAD SPRINGS, REBOUND
RUBBERS-
Continued
TRAILING ARM MOUNTING KIT-
Continued
HARDWARE AND FITTINGS,
securing brackets to
chassis frame
Bolt
4
Bolt
4
Washer,
plain
8
Nut,
nyloc
8
Shim,
for adjusting alignment
A/R
HARDWARE AND FITTINGS,
securing trailing arms to
inner and outer brackets
Bush,
pressed into trailing arms
4
Bolt,
trailing arm pivot
4
Washer,
plain
4
Nut,
nyloc
4
Road Spring,
stock grade
2
Road Spring,
mild competition grade
2
Insulator,
rubber, rear road spring
4
Rebound Rubber Assembly,
mounted on chassis frame
2
Rebound Rubber Assembly,
mounted on trailing arms
2
Rear Shock Absorber Assembly,
R.H.
1
Rear Shock Absorber Assembly,
L.H.
1
HARDWARE,
mounting rear shock absorbers to chassis frame
Screw,
set
4
Washer,
special
4
LINK ASSEMBLY,
rear shock absorbers to trailing arms
2
HARDWARE,
securing links to shock absorbers
Nut
2
Washer,
lock
2
HARDWARE AND FITTINGS,
mounting links to trailing
arms
Mounting,
rubber
4
Washer,
upper
2
Washer,
lower
2
Nut
2
Nut,
jam
2
Spacer,
rear spring, aluminium alloy
A/R
Please Note:
The alloy spacer listed here was designed
by Jaguar-Rover-Triumph as a cure for rear wheel
camber problems that were not solved by replacement
of rear road springs. Be aware that this
problem could indicate severe frame or suspension
damage that should be investigated before this
part is installed.
Plate No.
Part No.
Description
No. Off
