TRIUMPH TR6
PLATE DA
DIFFERENTIAL DETAILS--LATER UNIT
99
DIFFERENTIAL DETAILS--LATER UNIT
REAR AXLE COMPONENTS,
fitted after mid-1972 approx.
HOUSING ASSEMBLY,
rear axle center
1
Cap,
bearing
NSS
HARDWARE,
securing bearing caps to axle housing
Bolt
4
Washer,
lock
4
Plug,
oil level and oil filler
1
Plug,
oil drain, not fitted; TRF drills and taps cases of
1
all rebuilt units to take drain plugs
Carrier,
differential
1
Gear,
differential, side, sixteen teeth
2
Washer,
thrust, between side gears and carrier
2
Gear,
differential, pinion, ten teeth
2
SPHERICAL THRUST WASHERS,
adjusting clearance of
differential pinion gears
Washer,
.0465 to .0495 inch thick
A/R
Washer,
.049 to .051 inch thick
A/R
Washer,
.051 to .053 inch thick
A/R
Washer,
.053 to .055 inch thick
A/R
Washer,
.055 to .057 inch thick
A/R
Washer,
.057 to .059 inch thick
A/R
Washer,
.059 to .061 inch thick
A/R
Washer,
.061 to .063 inch thick
A/R
Washer,
.063 to .065 inch thick
A/R
Washer,
.065 to .067 inch thick
A/R
Washer,
.067 to .069 inch thick
A/R
Washer,
.069 to .071 inch thick
A/R
Washer,
.071 to .073 inch thick
A/R
Pin,
cross, differential
1
Pin,
locating cross pin in differential
1
Crown Wheel and Pinion Set,
1 to 3.7 ratio, carb
1
models
Crown Wheel and Pinion Set,
1 to 3.45 ratio, P.I.
1
models only
HARDWARE,
securing crown wheel to differential carrier
Bolt
10
Washer,
lock
10
Loctite 242 Threadlocker,
.20 fl. oz. tube
1
Bearing,
differential side
2
SHIMS,
adjusting clearance of differential side bearings
Shim,
.003 inch thickness
A/R
Shim,
.005 inch thickness
A/R
Shim,
.010 inch thickness
A/R
Bearing,
pinion head
1
Plate No.
Part No.
Description
No. Off
REAR AXLE COMPONENTS-
Continued
WASHERS,
adjusting fore and aft location of pinion,
fitted between pinion head and pinion head bearing
(These were used in production at the factory and
not supplied as spare parts.)
Washer,
adjusting, .0300 inch thickness
1
Washer,
adjusting, .0315 inch thickness
1
Washer,
adjusting, .0330 inch thickness
1
Washer,
adjusting, .0345 inch thickness
1
Washer,
adjusting, .0360 inch thickness
1
Washer,
adjusting, .0375 inch thickness
1
Washer,
adjusting, .0390 inch thickness
1
Washer,
adjusting, .0405 inch thickness
1
Washer,
adjusting, .0420 inch thickness
1
Washer,
adjusting, .0435 inch thickness
1
Washer,
adjusting, .0450 inch thickness
1
Washer,
adjusting, .0465 inch thickness
1
Washer,
adjusting, .0480 inch thickness
1
Washer,
adjusting, .0495 inch thickness
1
Washer,
adjusting, .0510 inch thickness
1
SHIMS,
adjusting fore and aft location of pinion, fitted
between front of pinion head bearing race and
rear axle center housing (These were not used in
production at the factory, but they are supplied as
spare parts.)
Shim,
.003 inch thickness
A/R
Shim,
.005 inch thickness
A/R
Shim,
.010 inch thickness
A/R
Spacer,
collapsible between pinion head bearing and
1
pinion shank bearing
Bearing,
pinion shank
1
Oil Seal Assembly,
front of casing
1
Flange,
pinion
1
Please Note:
The front mounting bracket must be
installed before the pinion flange is finally secured.
HARDWARE,
securing pinion flange onto pinion shaft
Washer,
plain
1
Nut,
nyloc, special
1
Shield,
pinion Nut
1
(Continued on next page.)
Plate No.
Part No.
Description
No. Off
