The Roadster FactoryThe Roadster Factory
TR6 Master Catalogue—Vol. 2 (Green)
Table of Contents
LOGIN | VIEW CART | CHECKOUT
View Shopping Cart -
Search
                          10   < Previous Next >        
TRIUMPH TR6
PLATE HF
HIGH-PERFORMANCE COMPONENTS
CLUTCH, GEARBOX, DIFFERENTIAL
109
HIGH-PERFORMANCE COMPONENTS--CLUTCH, GEARBOX, DIFFERENTIAL
FLYWHEEL
HF1
Flywheel,
aluminium, fitted up to eng. nos.
1
CC/CP50000; requires machining
Flywheel,
aluminium, fitted after eng. nos. CC/CP50000,
1
requires machining
Flywheel,
lightened stock flywheel with new starter ring
1
gear, weighs 14.5 lbs. approx.; fitted up to eng. nos.
CC/CP50000
Flywheel,
lightened stock flywheel with new starter ring
1
gear, weighs 18.7 lbs. approx.; fitted after eng. nos.
CC/CP50000
CLUTCH
HF2
Clutch Pressure Plate,
for high-performance street
1
engines
Clutch Pressure Plate,
for race engines
1
HF3
Clutch Driven Plate,
for high-performance street engines
1
Clutch Driven Plate,
for race engines
1
HF4
MAGIC CLUTCH KIT;
expected to give  long and trouble
1
free service; includes pressure plate, driven plate, and
Koyo-brand throw-out bearing installed on a new
throw-out sleeve
HF5
MAGIC CLUTCH KIT;
as above but with Gunst throw-out
1
bearing
HF6
Throw-out Bearing Kit,
high-tech, Gunst brand
1
GEARBOX
HF7
Close Ratio Gear Set;
fits earlier gearboxes with bronze
1
second gear bushes; ratios:  1st-2.19; 2nd-1.57;
3rd-1.23; 4th-1.00
Close Ratio Gear Set;
fits later gearboxes with steel
1
second gear bushes; ratios:  1st-2.99; 2nd-2.10;
3rd-1.39; 4th-1.00
Close Ratio Gear Set;
currently available type at the
1
time of writing; fits all TR6 gearboxes but requires
use of special clutch driven plates listed below;
ratios:  1st-2.19; 2nd-1.57; 3rd-1.23; 4th-1.00
CLUTCH DRIVEN PLATES,
for use with currently
available close ratio gear sets
Clutch Driven Plate,
for 1.0-inch, 10-spline input
1
shaft included with currently-available close-ratio
gear sets; high-performance clutch disc with springs
Clutch Driven Plate,
for 1.0-inch, 10-spline input
1
shaft included with currently-available close-ratio
gear sets; high-performance clutch solid clutch
disc without springs
HF8
Manual Transmission Fluid;
by G.M.; specifically
A/R
designed for all synchronized high-performance
gearboxes, 1 qt. bottle
Plate No.
Part No.
Description
No. Off
DIFFERENTIAL REBUILDING
RFK???
BEARING AND SEAL KIT,
differential
1
CROWN WHEEL AND PINION SETS,
for diffs
with solid spacers between pinion bearings
HF9
Crown Wheel and Pinion Set,
3.45 : 1 ratio
1
Crown Wheel and Pinion Set,
3.7 : 1 ratio
1
Crown Wheel and Pinion Set,
4.1 : 1 ratio
1
Crown Wheel and Pinion Set,
4.3 : 1 ratio
1
Crown Wheel and Pinion Set,
4.55 : 1 ratio
1
Crown Wheel and Pinion Set,
4.875 : 1 ratio
1
CROWN WHEEL AND PINION SETS, for diffs
with collapsible spacers between pinion hearings
Crown Wheel and Pinion Set,
3.45 : 1
1
Crown Wheel and Pinion Set,
3.7 : 1
1
HF10
"Limited Slip'' Differential;
replaces stock crown wheel
1
carrier inside axle center housing, Quaiffe brand
torsion sensing mechanical advantage type
ADDITIONAL CROWN WHEEL AND PINION
SETS,
supplied by Revington TR
RTR1228
Crown Wheel and Pinion Set,
5.13 : 1
1
RTR1227
Crown Wheel and Pinion Set,
5.25 : 1
1
RTR1278
Crown Wheel and Pinion Set,
6.67 : 1
1
DIFFERENTIAL MOUNTING KITS
HF11
Mounting Kit,
differential; includes a full set of
1
urethane mounts and nyloc nuts
Mounting Kit;
purple urethane mounts by Super
1
Pro; includes four front mounts and two rear mount
assemblies; STANDARD RIDE
Diff Mounting Kit;
purple urethane mounts by Super
1
Pro; includes four front mounts and two rear mount
assemblies; FIRM RIDE
Plate No.
Part No.
Description
No. Off








                        10   < Previous | | | | | | Next >        

This Zenscript catalog conversion was performed by zeni.net internet services. If you have questions about this interface, contact support@zeni.net. Cookies and Javascript must be enabled for online ordering, but these pages should render in a viewable manner in any style-sheet capable browser.